Interactive Table

 Interactive Table   

                                    Use GLOVIEW interactive kit--FP3 Board

 

　　Case 1: Use in class room

　　Case 2: Use in meeting room

　　Case 3:Use in Kitchen,Mall and Restaurant

　　Introduction:

　　FP3 BOARD    +    Table   =    Interactive Table

　　Use the interactive kit-FP3board attach to the table, then make the projection screen on the table to be touch screen. It use Laser Image Calibration Technology (LICT).

　　Put a laser emitter module inner the upper frame of the board.. It emits infrared laser curtain on the surface which is about 1mm thick invisible light and parallel with the projection screen surface, 1-2mm above the screen surface. When the fingers or any non-transparent objects touch this virtual surface, the light will be reflected and detected by the sensor. Computer will figure out the position of the mouse by accurate calculating the reflected light position.

　　Function and features introduction

　　1.High stability: Use the advanced algorithm to avoid the affect of the light.

　　2.Support plenty of gesture recognition: write with single finger; move with two fingers; eraser with palm; two fingers for zoom in& zoom out; two fingers work as scroll bar and so on.

　　Gesture recognition in Windows

　　3.5s auto calibration (as Picture A). Infrared technology and Optical technology only support manual calibration. Our auto calibration is much more accuracy and easier to operate.

　　4.Support 10 points finger touch (10 people can write together) (as Picture B)

　　5.Support Larger active size: support 40-100” for the room with sunlight (if the room without sunlight, it can support the active size of 40-120”).

　　6.Portable, high integration and easy to install: Total weight is only around 500g. The installation is very easy, just needed to put the emitter part on the table, and the sensor mounted to projector .No skill needed.

　　7.The product is smaller. Emitter part size is 3.5cm*20cm*1.7cm;

　　8.Wireless connection: Wireless connection between emitter and sensor, and sensor wireless control the emitter’s on and off. This make product more durable.

　　9.Sensor’s filter with auto push-pull device: When do auto calibration, the filter will be open; after calibration, the filter will be closed automatically. Such action makes the product more stable to defense the interference light, and the auto calibration success easier.

　　10.Any non-transparent object can be used as pen, like a rolled paper. In any active area, any non-transparent object can work instead of the pen and the mouse.

Technical Parameter:
 

Interactive Kit—FP3 Board
Calibration	Automatic(5s) / Manual (25/36 points)
Gesture Recognition	Gesture Recognition In Education Software:Write with single finger,Erase with palm, Two fingers for move,Two fingers away for zooming out and zooming in,Stay 2s with palm for opening spotlight,Double slap with palm for backing to desktop. In Windows:Max,Min windows,Zoom in or Zoom out or Rotate the picture, One finger as a scroll bar,Display all the windows,Shift windows.
Multi-touch	Ten points touch, write and eraser can do together.
Latency	<30ms
Filter	Software auto-control, enhance stability.
Minimum Active Size	40 inch
Max Active Size	100inch ( the room with light-proof curtain,excludes double screen )
Technology	Laser Image Calibration Technology
Positional Accuracy	±1 Pixel (Resolution: 4096*4096)
Aspect Ratio	4:3；16:9；16:10
Projection ratio	Ultra short throw:0.28,  FP3ENGLB4, installation distance:0.40~0.55M; Short throw:0.34,      FP3ENGLA4, installation distance:0.54~1.10M； Long throw:1.34,      FP3ENGLE4, installation distance: 2.15-3.20M.   (Depends on 80’’ projection screen)
Power	5w
Power of Laser Beam	150mw*2
Power Requirements	5V/1.5A
Signal Refresh Rate	120fps
Connect	The sensor and computer are connected by USB Cable; Emitter and Sensor are wireless; Emitter just needs power.
Weight	0.5kg
OS Requirement	Windows XP, Vista, Windows 7, Windows 8
Software	Calibration software(driver) and GLboard(education software)
Certification	CE, FCC
Warranty	2 years
Package	1. Sensor 2.Emitter 3.Mounts 4.USB cable (12m) 5.Pionter 6.Power Adaptor 7. Manual

　
Educational software introduction